Westinghouse SE 6000 Manual de instalación descargar pdf (Pagina 10)

____________________________________________________________________________________________________

HID Corporation 9292 Jeronimo Road Irvine, CA 92618 USA TEL (949) 598-1600 (800) 237-7769 FAX (949) 598-1690

Web page, E-mail - www.prox.com - MultiProx Controller Installation Manual 6000-900 Rev F 10 of 27

6b. The LED’s and Beeper of each Reader have eight different modes of operation. The LEDs and beeper of

each Reader can be controlled using control commands issued by the Controller, or by external control via

the Wiegand interface. The various combinations possible are as follows:

Number SWB(1-8) SWG(1-8) SWR(1-8)

1. On On On

2. Off On On

3. On Off On

4. Off Off On

5. On On Off

6. Off On Off

7. On Off Off

8. Off Off Off

1. The standard (default) mode - The LED is normally red and flashes green and beeps when a card is

read. The green LED and beeper may be controlled through the control inputs on the respective channel

connector, TBW1 to TBW8. When the green LED control line is activated, the LED changes from red to

green as long as the line is asserted. The beeper sounds when the beeper control line is activated. The LED

and beeper may be controlled independent of each other.

2. The LED is normally red and only the green LED is flashed when a card is read. The beeper does not

sound unless Controller by the external control line. The green LED and beeper may be controlled through

the control inputs on TBW1 to TBW8.

3. The LED is normally red and only the beeper beeps when a card is read. The green Led and beeper may

be controlled through the control inputs on TBW1 to TBW8.

4. The LED is normally red and when a card is read the LED and beeper do not flash or beep. The green

Led and beeper may be controlled through the control inputs on TBW1 to TBW8.

5. The LED is off and flashes green and the beeper sounds when a card is read. The red LED, Green LED

and beeper may be controlled through TBW1 to TBW8.

6. The LED is off and flashes green when card is read. The red LED, Green LED and beeper may be

controlled through TBW1 to TBW8.

7. The LED is off and the beeper sounds when a card is read. The red LED, Green LED and beeper may be

controlled through TBW1 to TBW8.

8. The LED is off and when a card is read the LED and beeper do not flash or beep. The red LED, Green

LED and beeper may be controlled through TBW1 to TBW8.

Theory of Operation

MultiProx Controller Operation

The MultiProx Controller is the main processing unit of the MultiProx system. The Controller consists of a

microprocessor, RF filters, and communications and interface electronics . It is the task master that schedules the

reading of HID proximity card, SE command cards, communications for control of the LEDs and Beeper on the

Reader, communication with the HSMs, converting/calculating card numbers and facility code, Wiegand message

building and Wiegand message output. The Controller uses a polling scheme to divide its time between each of

the eight Reader channels. At each channel, the Controller will enable the HID read sequence, the SE sequence

and communicate with the HSMs. The Controller polls channel one through eight until a card or HSM status

change occurs.

The MultiProx Controller reads HID proximity cards and SE command keys by sending commands that tell the

Reader to alternate between the two reading modes. Once the HID proximity cards or Schlage cards are

energized, a signal that corresponds to the encoding of the card is sent to the Controller. The Controller interprets

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 26 27

Comentarios a estos manuales

Sin comentarios

Westinghouse SE 6000 Manual de instalación Pagina 10

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Westinghouse SE 6000